Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Inspection for Richardson Homeowners
A chimney inspection in Richardson tells you what condition your flue, firebox and cap are actually in, and that answer matters more here than in most places. North Texas has a long cooling season and a lot of homes running wood-burning fireplaces and gas inserts at the same time, so creosote, cracked tile, thin mortar and rusted dampers all get a chance to build up quietly between uses. Our technicians have up to 15 years of experience and work the full set of chimney trades – sweep, inspect, repair – so you’re not calling three different contractors to get one straight answer.
We inspect with a camera, photograph what we find, and put it in front of you before anyone recommends a repair. Estimates are free, and the price is set per job by the written estimate. Call (888) 873-4715. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Fireplace Inspection
Fireplace Inspection is the close look at the fireplace itself – the firebox, damper, smoke chamber, hearth and the firebrick around the opening – rather than the length of the flue above it. You need one when the fireplace has sat unused for a season or more, when smoke rolls into the room instead of up the chimney, when a gas or wood insert has been added, or when you’ve just bought a home in Richardson and don’t know how the last owner ran it. We check the firebrick, look for gaps and spalling, confirm the damper opens and seals, inspect the smoke chamber for rough or missing parging, and photograph the findings. A fireplace inspection in Richardson typically runs $125-$250 depending on fireplace type and access. Anything structural that turns up gets priced separately in writing, so the fireplace part of the job is never a surprise.
Firebox and Damper Check
We examine the firebox walls for cracks, loose brick, and missing mortar joints, then test the damper for a clean open-close and a tight seat when closed. A damper that won’t seal lets conditioned air escape year-round and can also let smoke drift down when the fireplace is off.
Smoke Chamber and Hearth
The smoke chamber is the sloped section above the damper, and rough or unparged brickwork there is a common cause of a smoky fireplace. We note the condition and tell you plainly whether smoothing it out is worth doing or can safely wait.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Inspection Services
Chimney Inspection Services are the broader assessment of the whole venting system – cap, crown, flashing, flue, firebox and the exterior masonry – documented so you know what you have. You need this when a home is changing hands, after a chimney fire or a lightning strike nearby, when a new appliance has been installed, or whenever you haven’t had the chimney looked at in a few years. We run through the exterior first, then the interior, then the flue with a camera. Chimney inspection services in Richardson typically run $150-$450, with the higher end reflecting a Level 2 inspection with camera work and a written photo report. We work with professional-grade components when something needs replacing, and we tell you when the honest answer is that nothing does. If a chimney repair is needed, we’re the company that handles it rather than handing you off to another contractor.
Exterior and Crown Assessment
We look at the crown for cracking, the flashing where the chimney meets the roof, the cap and spark screen, and the masonry joints on all four sides. These are the parts that let water in, and water is the most common cause of chimney deterioration in North Texas.

Written Photo Documentation
Every inspection comes with photos of what we found, shown to you in person and left with you afterward. If someone ever tells you the liner needs replacing, you’ll have the images to compare against that claim.

Chimney Flue Inspection
Chimney Flue Inspection is the dedicated look down the inside of the flue – the passage the smoke and gases actually travel – checking for creosote buildup, cracked or missing flue tiles, gaps at the joints, and obstructions like nests or leaves. You need it after any chimney fire, when you’re burning more than usual, when the fireplace smells strong in warm weather, or when there’s no record of the flue ever being examined. We run a camera the full length of the flue and check the liner material against the appliance it serves. A chimney flue inspection in Richardson typically costs $150-$300, and it’s included in the Level 2 inspection price rather than added on. If the flue needs relining, we install DuraFlex flexible liner systems, which let an aged flue be brought back into service without rebuilding the chimney.
Creosote and Obstruction Check
We measure the creosote stage and depth, and we check for blockages that reduce draft or, worse, let carbon monoxide back into the house. The technician codes are standard in the trade, and we’ll explain what the reading means for you rather than just handing over a number.
Liner Condition and Fit
A flue liner needs to match the appliance – a wood fireplace, a gas insert and a wood stove each want a different size and material. We confirm the liner is intact, correctly sized and properly connected at the top and the appliance collar.
Chimney Fire
Chimney Fire damage is what we’re most often called out to assess, and it’s a chimney problem in its own right rather than just a dramatic event. A chimney fire happens when creosote ignites inside the flue, and it can burn hot enough to crack tiles and warp a damper without ever being visible from the living room. You need an inspection after any suspected chimney fire, even one you think you put out yourself. We examine the flue for cracked tiles, check the smoke chamber and firebox for heat damage, test the damper, and look at the exterior masonry for cracks. Post-fire inspection and repair in Richardson typically runs $250-$900 depending on what the fire damaged, with relining priced separately if the flue is compromised. The safety point here is simple: don’t light another fire until the flue has been checked.
Signs of a Chimney Fire
Look for a loud roaring or popping sound, flames or sparks at the top of the chimney, a strong hot smell, or puffy, honeycombed creosote inside the flue afterward. Damage is often internal and invisible from outside, which is exactly why the camera matters.
Why It Can’t Wait
A cracked flue tile lets heat and embers reach the framing of the house, and it also lets carbon monoxide escape into the living space. Until an inspection clears the flue, the chimney isn’t safe to use.
Level 2 Chimney Inspection
Level 2 Chimney Inspection is the standard formal inspection for a real estate transaction, an appliance change, or any suspected problem – it goes beyond the basic visual check and includes video of the flue interior. The levels come from the industry standard, and Level 2 is what most buyers and sellers in Richardson actually need when a house changes hands. We inspect all accessible parts of the chimney and venting, run a camera through the flue, check the attic and crawl space penetration where accessible, and document the findings in writing with photos. A Level 2 chimney inspection in Richardson typically costs $250-$450. This is the inspection that answers the question a home inspector can’t: is the flue actually serviceable, or is it going to need a liner?
When a Level 2 Is Required
Real estate transactions, a new wood stove or insert, a change in fuel type, an earthquake or chimney fire, and any ongoing performance problem all call for Level 2. A standard sweep alone won’t tell you what a Level 2 will.
What the Report Includes
You get the camera footage, still photos of anything notable, and a written summary separating what needs attention now from what can wait. We don’t lump everything into “urgent” to justify a bigger bill.
Chimney Leak
Chimney Leak problems show up as water stains on the ceiling near the chimney, a damp firebox, rusted damper hardware, or white efflorescence on the exterior brick. They’re rarely a mystery once you get up there and look. You need a leak inspection when you see any of those signs, after a heavy rain season, or when the fireplace smells musty in humid weather. We check the crown, the flashing where the chimney meets the roof, the cap, the brick joints, and the flue itself for water entry points. Chimney leak diagnosis in Richardson typically runs $150-$350, and the repair is priced separately once we know the source. Caps and covers from Gelco and Olympia Chimney and flashing from Famco are built specifically for this work, which is why we use them instead of generic roofing-store substitutes that fail at the first hard rain.
Common Water Entry Points
A cracked crown, failed flashing, an open flue with no cap, and deteriorated mortar joints account for most chimney leaks. Each one has a different fix, and putting a cap on a flashing problem doesn’t stop the water.
Leak Repair Materials
We match the repair to the source: a new crown, new flashing, new mortar, or a proper cap with a spark screen. Sealing the exterior without finding the source is a temporary patch at best.
Chimney Camera Inspection
Chimney Camera Inspection is the video look inside the flue that turns a guess into evidence, and it’s the part of the job we treat as non-negotiable. You need one whenever the flue’s condition is unknown – after a chimney fire, before an insert goes in, during a real estate transaction, or any time a rep from another company says you need a liner. We run a camera down the full length of the flue, record it, and show you the footage on site so you can see the cracks, the creosote or the obstruction yourself. Chimney camera inspection in Richardson typically runs $150-$300, and it’s included in our Level 2 inspection rather than charged as an add-on. Nothing gets recommended without evidence you can see.
Recording and Review On Site
You watch the footage with the technician and ask questions right there. It’s your chimney, and you should see what’s happening inside it before you spend money on a repair.
Catching What a Visual Misses
A flashlight from the firebox only shows the first few feet. The camera finds hairline tile cracks, gaps at joints, and offset flues that a visual check can’t reach.
Brands We Service
We work with DuraFlex flexible liner systems and know where they wear and how they’re connected at the top plate and the appliance collar, which is where most relining problems actually start. We install HeatShield for resurfacing a damaged flue – it’s a repair-grade ceramic product not available through general contractors, and it’s the right call when the flue structure is sound but the surface has failed. We source caps, covers and weatherproofing from Gelco and Olympia Chimney, and flashing and venting components from Famco, because those brands are purpose-built for chimney work rather than adapted from roofing stock. Copperfield components round out the repair side and are trusted across the trade. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco or Copperfield in place, or any other make, we can help – the inspection tells us what’s there before anything is specified.
You’ll never be told you need a full rebuild when a reline or a resurfacing will do the job. Our technicians have up to 15 years of experience, and the recommendation comes from what the camera found, not from what’s easiest to sell.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke backing into the room. That’s a draft or flue obstruction problem, not a firewood problem. It usually points to a blockage, a damper that won’t open fully, or a flue that’s the wrong size for the appliance, and it gets worse the colder it gets.
- Strong creosote smell in warm weather. The smell is a sign of creosote buildup that’s absorbing moisture. It’s also a warning that the flue needs sweeping before the next burning season, and possibly a camera inspection.
- Water stains or efflorescence on the chimney. White powder on the brick or a damp ceiling near the chimney means water is getting in through the crown, flashing or cap. Left alone, water freezes in the masonry and cracks it open.
- Any roaring sound or popping from the chimney. That’s the sound of a chimney fire. Even if it stops quickly, the flue needs inspection before the fireplace is used again.
- A newly bought home with no inspection record. A home inspector doesn’t inspect the inside of a flue. A Level 2 chimney inspection is the only way to know what you bought.
Our Process, Step by Step
- 1
Talk through what’s happening. We ask about the appliance, how often you burn, what you’ve noticed, and whether there’s a home sale or a new insert in the picture. That conversation decides which level of inspection you actually need.
- 2
Inspect the exterior and the fireplace. We check the cap, crown, flashing, exterior masonry, firebox, damper and smoke chamber. Everything gets photographed.
- 3
Run the camera down the flue. We record the full length of the flue and show you the footage on site, so the evidence is in front of you rather than in a report you never see.
- 4
Explain what we found and what it needs. We separate what has to be fixed now from what can wait, and we’re comfortable telling you when the answer is nothing. Repairs are quoted in writing, with the brand and material named.
- 5
Do the work if you want us to. Sweeping, relining with DuraFlex, resurfacing with HeatShield and weatherproofing all come from the same company, so you’re not coordinating a sweep, a repair and an inspector separately.
How Much Does Chimney Inspection Cost in Richardson?
Chimney inspection in Richardson typically costs $150-$450, with the level of inspection and the condition of the chimney driving the number. A basic visual inspection at the low end runs $125-$200. A Level 2 inspection, with camera work and a written photo report, runs $250-$450. If your chimney needs sweeping first, that’s priced separately and usually sits in the $180-$350 range depending on how much creosote is present and whether the roof is easily accessed.
What affects the price is mostly access and complexity: a steep roof, a chimney with multiple flues, a wood stove or insert, or a masonry chimney with a complex crown all take more time. A simple single-flue fireplace on a walkable roof is at the lower end.
To avoid overpaying, ask for the findings in writing with photos and ask which level of inspection you’re paying for. If someone recommends a liner or a rebuild without showing you the camera footage, get a second opinion. That’s the single best protection you have as a homeowner.
A free estimate from us includes the inspection findings, a written quote naming the material, and a plain answer on what can safely wait. We don’t recommend work your chimney doesn’t need. Call (888) 873-4715 for an exact quote – estimates are free.
Our Service Area Near Richardson
We inspect chimneys across Richardson and the surrounding corridor, including Richardson itself and the neighboring towns of Fairview, Lucas, Wylie, Rockwall, Lavon, Fate, Princeton, Prosper and Royse City. If you’re just north of us in Lucas or out toward Wylie, we can book you in the same week in most cases. Dispatch runs Sunday through Friday, 7am to 7pm. Homeowners further out toward Princeton or Royse City should call and we’ll confirm the earliest opening.
Serving Richardson, TX – Our Local Coverage Area
We serve Richardson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Inspection in Richardson
A chimney inspection is a documented assessment of the chimney’s condition – the flue, firebox, damper, cap, crown, flashing and exterior masonry – done to find problems before they become expensive or dangerous. It goes beyond sweeping. The inspection looks at the whole system and reports back in writing with photos, so you know what your chimney needs and what it doesn’t. Call (888) 873-4715 for an exact quote – estimates are free.
A basic inspection usually takes 45 minutes to an hour, and a Level 2 inspection with camera work and a written report runs about 1.5 to 2 hours. The time depends mostly on roofline access and how many flues the chimney has. If sweeping is added, expect a bit longer. Your technician will tell you what to expect before starting.
A chimney inspection in Richardson typically runs $150-$450. A Level 2 inspection with camera work and a written report sits at $250-$450, while a basic visual inspection is at the lower end. The written estimate sets the final price, and estimates are free. Call (888) 873-4715 to get the exact number for your chimney.
Yes – we install and work with DuraFlex flexible liner systems, and we use HeatShield ceramic resurfacing for damaged flues. Both are contractor-trusted product lines we’ve specified on many jobs. We also source caps and covers from Gelco and Olympia Chimney, and flashing and venting from Famco and Copperfield components. Whether you have those brands or another make, we can inspect and advise on it.
Same-day inspection is often possible if you call early. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (888) 873-4715 and we’ll find the earliest slot for your Richardson home.
The inspection itself is a documented assessment with no warranty attached, because it’s a report on what we found. Repairs we install – relining, resurfacing, cap and flashing work – carry the standard manufacturer warranty on the product plus our workmanship backing. The specific terms are put in writing on your estimate before any work starts, so there’s no ambiguity afterward.
Clear the area around the fireplace, don’t build a fire that day, and open the damper so the technician can check it. Note any issues you’ve seen – smoke backing up, smells, water stains – and have your burning history in mind, since it tells us whether you need a basic or Level 2 inspection. Access to the attic and roof is helpful if it’s safe to reach. Call (888) 873-4715 if you have questions before your appointment.
Schedule Your Chimney Inspection Service in Richardson Today
Book a chimney inspection with Ridgeway Chimney Sweep and get a clear answer on the condition of your flue, documented in photos you can keep. Our technicians have up to 15 years of experience, and we tell you what your chimney actually needs – nothing more. Call (888) 873-4715 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Ridgeway Chimney Sweep.