Chimney Repair in Richardson, TX | Ridgeway Chimney Sweep

Chimney Repair in Richardson - Inspected on Camera, Then Priced in Writing

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Richardson Homeowners

A cracked chimney crown, a rusted cap, or a flue that no longer drafts cleanly is the kind of problem that doesn’t announce itself. It shows up as a faint stain on the ceiling near the fireplace, a smell that lingers after a fire, or a masonry joint that crumbles when you touch it. In Richardson, where wood-burning fireplaces are common in the older neighborhoods off Central Expressway and in the newer builds out toward Breckinridge, the fix depends entirely on what the chimney actually needs. Our technicians have up to 15 years of experience with sweep, inspect, and repair under one roof, so you aren’t coordinating three contractors. Same-day service is often possible. Call (888) 873-4715 and we’ll get a written estimate in front of you before any work begins.

Call (888) 873-4715

Chimney Cap Installation

Chimney Cap Installation is the fitting of a purpose-built cover over the flue opening to keep rain, animals, and debris out while allowing smoke and gases to escape. You need one if your flue is open to the sky, if you’ve found birds or squirrels in the firebox, or if water is getting into the flue on rainy days. We install caps sourced from Gelco and Olympia Chimney, both made specifically for chimney weatherproofing rather than generic hardware-store substitutes, and we size the cap to the actual flue dimensions so it sits correctly and lasts. A proper stainless or copper cap typically runs $250 to $600 installed, depending on size and material. The written estimate sets the final price.

Stainless and Copper Cap Options

Stainless steel caps hold up to Richardson’s sun and occasional hail and are the practical choice for most homes. Copper caps cost more but develop a patina over time and suit historic or higher-end properties. We’ll show you the difference in person so you can decide.

Single-Flue vs. Multi-Flue Caps

Most Richardson homes have a single flue, but ranch-style chimneys with two or three flues need a multi-flue cap built to span the whole crown. We measure the crown footprint and the flue spacing before ordering, so the cap fits over every opening without gaps.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is the removal of a failed, rusted, or storm-damaged cap and the installation of a new one sized to the same flue. You need it when the mesh has torn, when the top has rusted through, when a hail storm has dented it flat, or when the old cap was the wrong size to begin with and never sealed properly. We work with Olympia Chimney caps because they’re built for the job, and we check the crown and flue tile condition while the cap is off, since that’s the one time we can see them clearly. Replacement typically runs $250 to $550 installed. The written estimate sets the final price. If you’re already booking a chimney repair, we can fold the cap replacement into the same visit.

When a Cap Is Beyond Repair

A cap with a rusted top plate or a mesh that’s pulling away from the frame isn’t worth patching. Once the structure is compromised, water gets in and the next hail storm finishes the job. We’ll tell you plainly when replacement is cheaper than repair.

Matching the New Cap to the Old

We photograph the old cap before removal so the new one matches the profile and fits the same flue tile. That matters on homes where the cap is visible from the street and an ill-fitting replacement would look wrong.

Chimney Liner Installation

Chimney Liner Installation is the fitting of a new flue liner inside the chimney to carry smoke and gases safely to the top. You need it when the existing clay tile liner is cracked, when the flue is unlined, when you’ve switched to a new appliance that requires a different flue size, or when a camera inspection shows gaps that could let heat reach combustible framing. We install DuraFlex flexible liner systems, and we’re authorized to work with them, which matters because a flexible liner has to be sized, insulated, and terminated correctly or it won’t perform. We also use HeatShield ceramic resurfacing for liners that can be repaired rather than replaced. A full reline typically runs $2,500 to $6,000 depending on height, flue size, and insulation needs. The written estimate sets the final price.

DuraFlex Flexible Liner Systems

DuraFlex liners are the preferred solution for relining an aged or damaged flue without tearing into the chimney structure. They’re flexible enough to navigate offsets in older Richardson chimneys and durable enough to handle continuous wood-burning heat. We size them to the appliance, not to whatever’s on hand.

HeatShield Resurfacing as an Alternative

When the liner damage is limited to gaps and spalling rather than a full failure, HeatShield can resurface the existing flue from the inside. It’s a repair-grade product most general contractors can’t access or install correctly. We’ll tell you which route your chimney actually needs.

Chimney Flashing Repair

Chimney Flashing Repair is the correction of the metal seals where the chimney meets the roof, which is where most water intrusion starts. You need it when you see staining on the ceiling or the chimney breast, when the flashing is lifted or rusted, or when the roofing cement someone smeared on years ago has dried and cracked. We install Famco flashing and venting components because they’re made for chimney weatherproofing and hold up to the thermal movement between a hot chimney and a cooler roof. We also inspect the counter-flashing and the step flashing during the same visit, since one failing without the other is common. Flashing repair typically runs $300 to $900 depending on roof pitch and how much flashing has to be rebuilt. The written estimate sets the final price.

Why Flashing Fails First

Flashing takes the most movement of any part of the chimney assembly. When a chimney heats and cools season after season, the metal flexes and the seal at the roof line opens. That’s why water shows up at the ceiling before it shows up anywhere else.

Step Flashing and Counter-Flashing

Step flashing runs along the roof slope against the chimney wall; counter-flashing covers the top edge. Both have to be replaced together or the repair won’t hold. We check both before quoting.

Chimney Crown Repair

Chimney Crown Repair is the fixing or rebuilding of the concrete cap on top of the chimney that sheds water away from the flue and masonry. You need it when the crown is cracked, when pieces have spalled off, when it slopes the wrong way and lets water pool, or when you can see daylight through a crack from the firebox. We rebuild crowns with proper slope and a bonding break at the flue so the crown can move independently of the chimney without cracking. Crown repair typically runs $400 to $1,200 depending on size and whether the crown can be resurfaced or has to be poured new. The written estimate sets the final price. A failing crown is also the fastest way to ruin a liner, so we check both together.

Cracked vs. Rebuilt Crowns

Hairline cracks can often be sealed and resurfaced. A crown that’s broken into pieces or has lost its slope needs to come off and be poured new. We’ll tell you which one you’re looking at.

The Bonding Break at the Flue

The crown has to be separated from the flue tile by a small expansion joint. Without it, the flue and crown fight each other as they heat and cool, and the crown cracks again. We build that joint in every time.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they actually do and what they’ll stand behind, and knowing how to evaluate them is the difference between a fix that lasts and one that gets redone next season. You need to compare companies when a repair quote feels vague, when the diagnosis doesn’t include camera footage or photos, or when a contractor wants to do work a chimney sweep says isn’t necessary. We do sweep, inspect, and repair under one company, so the diagnosis and the fix come from the same place. We work in a curated set of professional lines – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield – and we’re glad to tell you which one applies to your job and why. Repair costs vary with the issue; the written estimate sets the final price.

Questions Worth Asking Every Company

Ask whether the company does its own inspections, what brand of liner or resurfacing product they use, and whether the diagnosis comes with photos you can keep. A contractor who can answer all three clearly is worth a longer conversation.

Reading a Repair Quote

A good quote names the problem, names the product going in, and states what’s included. If a quote lists only a price and a one-line description, ask for the detail. You’re entitled to know what’s being installed in your chimney.

Chimney Masonry Repair

Chimney Masonry Repair is the correction of damage to the brick and mortar above the roof line – repointing joints, replacing spalled brick, rebuilding a section that’s pulled away from the house. You need it when mortar joints crumble under a screwdriver, when bricks are flaking or falling, or when the chimney leans enough that you notice it from the yard. We repoint with mortar matched to the original brick, replace only the brick that’s actually failed, and rebuild sections where the structure has moved. Masonry repair typically runs $600 to $2,500 depending on the height and extent of the work. The written estimate sets the final price. If the damage reaches below the roofline, we flag it before anyone starts.

Repointing Instead of Rebuilding

Most masonry damage is at the joints, not the brick. Repointing the joints with the right mortar mix restores the chimney without replacing brick that’s still sound. It’s cheaper and it protects the original structure.

Spalled Brick and Water Damage

Bricks that flake or crumble on their face have absorbed water and spalled. We replace those units, but we also find the water path that caused them, because new brick in the same spot will do the same thing if the source isn’t fixed.

Brands We Service

We work with DuraFlex flexible liner systems and are authorized to install them, which means we know how they’re sized, how they handle offsets in older flues, and where the failure points show up. We also work with HeatShield ceramic resurfacing for liner repair – a repair-grade product that most generalist handymen cannot access or install correctly. Knowing how HeatShield cures and how it bonds to the existing flue is the difference between a resurfacing that lasts and one that peels.

On the weatherproofing side, we source caps and flashing from Gelco, Olympia Chimney, and Famco, all purpose-built for the chimney trade rather than big-box substitutes. We install Copperfield chimney components as well, and we know where each of these wears out on a Richardson chimney exposed to our sun and occasional hail. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Water stains on the ceiling or chimney breast. Staining usually traces back to failed flashing or a cracked crown, and both get worse with each rain. The sooner we see it, the less masonry work is needed.
  • Crumbling mortar between the bricks above the roof. If a joint crumbles when you press it, the chimney is losing structural integrity. Repointing early costs far less than rebuilding a section later.
  • A strong creosote smell that lingers after a fire. That smell usually means creosote buildup in the flue, and heavy buildup is the condition most closely tied to chimney fires. A sweep and inspection settle it quickly.
  • Smoke rolling back into the room. A flue that doesn’t draft is often blocked, undersized, or damaged. Don’t keep burning; get it looked at before the next fire.
  • Visible cracks in the crown or missing chunks of it. A failing crown lets water straight into the flue. That water damages the liner and the masonry behind it, so it’s worth a look before the next storm.

Our Process, Step by Step

  1. 1
    Book the visit. Call (888) 873-4715 and we’ll set a time. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
  2. 2
    Walk the chimney. We start at the firebox, check the damper and smoke chamber, and work up through the flue to the crown and cap. If a camera inspection is needed, we run it and show you the footage on the spot.
  3. 3
    Photograph and document. Every issue gets a photo you can keep. We don’t recommend work you can’t see evidence for, and we tell you plainly when something can safely wait.
  4. 4
    Write the estimate. The estimate names the problem, names the product going in – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or Copperfield as the job calls for – and states what’s included. The written estimate sets the final price.
  5. 5
    Do the work and check it. The same company that inspected does the repair, and we test the result – draft, seal, and fit – before we call it done.

How Much Does Chimney Repair Cost in Richardson?

Chimney repair in Richardson typically runs $250 to $6,000, and the range is wide because the work is wide. A typical chimney cap installation runs $250 to $600 depending on size and material. Chimney cap replacement runs $250 to $550. Chimney flashing repair runs $300 to $900 depending on roof pitch and how much flashing has to be rebuilt. Chimney crown repair runs $400 to $1,200 depending on whether the crown can be resurfaced or has to be poured new. Chimney masonry repair runs $600 to $2,500 depending on extent and height. Chimney liner installation, the largest line item, typically runs $2,500 to $6,000 depending on flue height, size, and whether insulation is needed.

What drives the price is the extent of the damage, the height and access of the chimney, and which product line the job calls for. How to avoid overpaying: get the diagnosis with photos, insist on a written estimate before work starts, and ask which product goes in. Nothing gets recommended without camera evidence you can see for yourself, and we say plainly when a repair can safely wait. What’s included in a free estimate: the on-site inspection, the camera footage if it’s needed, the written scope, and the flat price for the job. Call (888) 873-4715 for an exact quote – estimates are free.

Our Service Area Near Richardson

We serve Richardson and the surrounding towns, including chimney repair in Lucas, chimney repair in Wylie, and work in Fairview, Rockwall, Lavon, Fate, Princeton, Prosper, and Royse City. Drive time from Richardson to most of these towns is twenty to forty minutes, so scheduling is straightforward. If you’re booking a sweep and inspection at the same time as the repair, tell us on the call and we’ll plan the visit around both. Ridgeway Chimney Sweep covers sweep, inspect, and repair together – see Ridgeway Chimney Sweep for the full picture.

Serving Richardson, TX – Our Local Coverage Area

We serve Richardson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Richardson

Schedule Your Chimney Repair Service in Richardson Today

If your chimney needs a cap, a crown, a liner, or a masonry repair, the next step is a written estimate from a company that does the inspection and the repair together. Call (888) 873-4715. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a no-obligation estimate and a clear answer on what can safely wait.

Written by the team at Ridgeway Chimney Sweep.

Why Richardson Chooses Ridgeway Chimney Sweep

We set the standard for chimney repair in Richardson.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Richardson

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Richardson Customers Say

Trusted by homeowners across Richardson and surrounding areas.

★★★★★

"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."

Marisol Vargas
★★★★★

"Liner was cracked in two places. He walked me through the repair options honestly, including the one that was cheaper for him and better for me."

Kristen Miller
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Vivian Wong

Ready for Chimney Repair in Richardson?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Richardson.

(888) 873-4715

Request a Free Estimate in Richardson

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - We Answer 24/7